Looking forward to working with us
Product
Al-cu-mg-zn alloy, which is made by adding Zn on the basis of duralumin.
This kind of alloy is currently the highest strength of aluminum alloy, higher than other aluminum alloy strength, so called super hard aluminum.
Disadvantage is also very poor corrosion resistance, can improve the artificial aging temperature or aluminum.
More
This kind of alloy is currently the highest strength of aluminum alloy, higher than other aluminum alloy strength, so called super hard aluminum.
Disadvantage is also very poor corrosion resistance, can improve the artificial aging temperature or aluminum.
6063 aluminum alloy material. The main alloy elements are magnesium and silicon, with excellent machining performance, excellent weldability, extrusion and electroplating, good corrosion resistance, toughness, easy to polish, color film, excellent anodic oxidation effect, is a typical extrusion alloy.
6063 aluminum alloy profile with its good plasticity, moderate heat treatment strength, good welding performance and anodic oxidation treatment, gorgeous surface color and many other advantages, is widely used in building profiles, irrigation pipes, for vehicles, platforms, furniture, elevators, fences and other tubes, bars, profiles.
More
6063 aluminum alloy profile with its good plasticity, moderate heat treatment strength, good welding performance and anodic oxidation treatment, gorgeous surface color and many other advantages, is widely used in building profiles, irrigation pipes, for vehicles, platforms, furniture, elevators, fences and other tubes, bars, profiles.
Thickness: 0.2-10mm
Port of Destination: Any port you like
Application:Aluminum tread plates according to the different classification of aluminum sheet alloy
In accordance with the different patterns of aluminum plate classification: pattern plate has a bar, two bars, three bars and five bars.
More
Port of Destination: Any port you like
Application:Aluminum tread plates according to the different classification of aluminum sheet alloy
In accordance with the different patterns of aluminum plate classification: pattern plate has a bar, two bars, three bars and five bars.
1060 aluminum plate is widely used in products with low strength requirements.
Products are often used in signs, billboards, building exterior decoration, bus body, tall buildings and factory wall body adornment, kitchen sink, lamp holder, fan blade, electronic parts, chemical equipment, mechanical parts, deep drawing of sheet or spinning concave ware, welding part, heat exchanger, clock surface and plate, plate, kitchenware, ornaments, reflective equipment, etc.
More
Products are often used in signs, billboards, building exterior decoration, bus body, tall buildings and factory wall body adornment, kitchen sink, lamp holder, fan blade, electronic parts, chemical equipment, mechanical parts, deep drawing of sheet or spinning concave ware, welding part, heat exchanger, clock surface and plate, plate, kitchenware, ornaments, reflective equipment, etc.
The main alloying elements in 6061 alloy are magnesium and silicon, which have moderate strength, good corrosion resistance, weldability and good oxidation effect.
Widely used in various industrial structural parts requiring a certain strength and high antibiotic corrosion, its main chemical composition: Cu:0.15-0.4; Si: 0.4-0.8; Fe: 0.7 -; Mn: 0.15; Mg: 0.8-1.2; Zinc: 0.25; Cr: 0.04-0.35; Ti: 0.15 -; 6061 aluminum plate its state T6 and T651 difference is that in general, T6 internal stress will be relatively large, processing will be deformed, the most suitable for processing state should be T651, he is on the basis of T6 tensile, eliminate internal stress.
More
Widely used in various industrial structural parts requiring a certain strength and high antibiotic corrosion, its main chemical composition: Cu:0.15-0.4; Si: 0.4-0.8; Fe: 0.7 -; Mn: 0.15; Mg: 0.8-1.2; Zinc: 0.25; Cr: 0.04-0.35; Ti: 0.15 -; 6061 aluminum plate its state T6 and T651 difference is that in general, T6 internal stress will be relatively large, processing will be deformed, the most suitable for processing state should be T651, he is on the basis of T6 tensile, eliminate internal stress.
6082 is a heat-treatable alloy with good formability, weldability, machinability and corrosion resistance.
It also has moderate strength and can maintain good operability after annealing.
It is mainly used in mechanical structure, including bars, plates, pipes and profiles.
More
It also has moderate strength and can maintain good operability after annealing.
It is mainly used in mechanical structure, including bars, plates, pipes and profiles.
Tel
Sala A8-1-1007, Centro de negocios Hanyu Jingu, No. 7000, Jingshi Road, Zona de alta tecnología, Ciudad de Jinan, Provincia de Shandong
All rights reserved© TIANYI Steel (Shandong) Co., Ltd. Website Building 300.cn Jinan2 SEO Business License
